How To Repair Punch Hole In Wall

When a stroppy teenager doesn't become their way the starting time affair they want to do is dial something, and this usually leads to a punched hole in the wall!

If isn't a fist, its an Xbox controller and thanks to FIFA twenty, there are alot of teenagers punching walls over their lost matches…whats the world coming too??

The thing is, later the damage has been washed most parents accomplish for the metal patch you tin buy from your nearest DIY store.

They do the job, don't get me incorrect, but the finish is poor, even if y'all're good with a filling pocketknife.

I take a better manner of patching up a wall using a repair called 'The California drywall Patch'.

The California drywall patch method is probably the cheapest and gives you lot a improve end than most (if not all) patching methods.

How To Fix a Punched Hole In The Wall – YouTube Episode 2

What Do I Need to Fix a Punched Hole In The Wall?

When using the California drywall patch method for fixing a punched hole in the wall, you won't need whatever expensive tools, but I practise recommend you have the tools I suggest considering they will brand the job alot easier, and they are…

Pencil

Ruler

Stanley knife

Dry out wall saw

12 inch Taping pocketknife

Plastering Hawk

five in 1 tool/filling knife

Filler – I recommend Gyproc'due south Easi-make full jointing chemical compound

A scrap piece of plasterboard/drywall

Sandpaper, sanding cake

How To Fix A Punched Hole In The Wall Steps…

Stride One – Check For Wires and Pipes

Using your fingers, advisedly remove the damaged piece, and accept practiced experience round (all 360 degrees) for whatsoever wires or pipes.

Footstep Two – Prepping The Hole

Using a drywall saw carefully offset to saw the round pigsty into a square hole.

Stride 3 – Making The Patch

Offer the BACKSIDE of your chip piece of drywall upto the square hole y'all've made.

We want a 2 inch overhang all around the area of the square, marking each measurement onto the bit slice of drywall.

Rotate the drywall ninety degrees and make another 2, 2″ wide marks.

Using a ruler or a straight edge join those measurements together to brand a foursquare.

Once the lines are drawn, we need to cutting the square out using a Stanley knife.

Gently score one line kickoff, and so concord the plasterboard and tap with your kickoff on the opposite face of the plasterboard directly in line with the scored line yous've just fabricated.

Repeat the above process again for the other scored line.

You should now take a square that when offered up to the hole in the wall gives you a ii inch overhang on all sides.

With this cutting drywall foursquare we at present demand to transfer the inside dimensions of the square hole on to it.

And you this by offering information technology back up to the pigsty, making certain your ii inch overhang is equal on each side.

Grab a pencil and then make ii marks a quarter of an inch shorter of the edge.

Now using those marks we need to join them upward again until you have another square in the center of the drywall.

Score forth each line one at a fourth dimension, simply instead of cutting the scored piece off, we want to peel the plaster from the paper instead (see video also).

Hey Presto! you should at present accept a California drywall patch ready for action!

Step Four – Test Fit Patch

We now need to test fit the California drywall patch to brand certain it fits into the foursquare hole we made earlier.

By placing the patch over the hole without applying too much pressure endeavour to push button the patch into the hole.

If the patch doesn't fit, then conform the pigsty not the patch, past running your Stanley knife or drywall saw effectually the inside edge of the pigsty until plenty drywall is removed then the patch can slide in and fit flush.

Now offer the patch upward to the hole over again and it should fit nice and comfortably in the wall without adding also much pressure.

Footstep 5 – Mix Filler

Using your hawk, cascade some dry filler onto it, then make a crater in the middle of the filler.

We want to add hot water to the filler considering it will speed the drying time, helping this patch exist a quicker ready than normal.

If your scared of a fast drying fourth dimension, just add cold water.

Give the filler a practiced mix using your filling/putty pocketknife until the filler resembles whipped cream.

Step Vi – Applying Filler To The Hole and Patch

Load upwardly your filling/putty knife with filler and paste on all 4 sides of the hole.

And so property your patch place filler into the corners of the four sides where the paper meets the plaster.

This will ensure no air pockets class when you push the patch into the hole, information technology also creates a stronger repair.

Take the loaded patch and place into the hole, using your putty knife push on each corner to make certain the patch sits affluent with the wall.

Gently with the filler/putty knife, slide the pocketknife across the paper edges until the paper is stuck downwardly with the filler

Removing any excess filler as yous go.

Step Seven – Skim The Repair

With the leftover filler, take hold of a 12″ taping knife, scoop the filler up and skim the filler across the repair.

Try to continue your taping knife at well-nigh 20-30 degrees as you pull information technology beyond the repair.

Don't be besides perfect considering you volition be sanding this coat downwardly once information technology's dry

Pace Eight – Sand Down Start Skim and Apply 2d Skim

At present the first skim glaze is dry we need to sand it down until it is smooth and flush to the surface of the wall.

Mix another application of Easi-make full on your hawk.

SHERLOCK MAINTENANCE TIP: If you find too difficult to mix the filler on your militarist, cascade the filling compound into an onetime container, add together water and mix. In one case information technology resembles whipped foam transfer it to your hawk…Sorted!

Apply the second glaze of skim slightly wider than the get-go coat of skim. This helps feather the repair back into the wall.

Step Nine

Wait for the 2d glaze of skim to dry and repeat the same sanding procedure making certain all ridges and high spots are sanded down flush with the wall.

So wipe downwardly sanded area with a slightly clammy cloth.

Step Ten

At present get painting your repair.

If you find afterward the pigment dries there is some high spots or ridges you may of missed when sanding, just expect for the paint to completely dry out, rub downwardly and repaint.

Did This Post Aid?

Hopefully you now know how to fix a punched hole in the wall.

It is a bully skill to take, filling holes this way is by far the best repair.

Let me know if you constitute it easy post-obit the steps above in the comments department below.

Each and every week I put my heart and soul into providing you with corking content to help with any DIY jobs around the home.

If yous think this postal service could help someone you know, please share.